"Low-temperature jelly" is the most common complaint with natural oil soap systems, and it comes from the change in crystalline form of fatty acid soaps at low temperature. Our approach is to solve it at the raw material stage rather than leave you to patch it later:
· The natural oil soap series uses a homogeneous reaction with multi-stage temperature control; the stated strengths on the product page are high active content and good low-temperature behaviour
· Choose grades marked cold-processable: DCK-45M, DCK-45H, DCP-30H, DCB-45H, DCB-40M, KS-300 — low-temperature stability and thickening were designed in from the start
· If extra reinforcement is needed, SUPGEL 703N (transparent systems) or Betone BW can raise heat resistance
If jelly has already appeared, first check whether the free fatty acid ratio in the formula is too high, then consider changing grade. Masking it with solvent usually costs you foam.
Poor heat resistance usually shows up as separation at elevated temperature, thinning paste, or settling of particles. It can be improved directly from the raw material side:
· SCA-75 (potassium cocoyl glycinate + hydroxystearic acid, patented) — the product page explicitly states improved system heat resistance
· SUPGEL 703N and Betone BW — improve heat resistance and also provide suspending capability
· DCB-45H / DCB-40M — long-lasting foam stability, easy to thicken, slower foam decay at high temperature
Two frequently overlooked points: too much headspace in the pack accelerates oxidation at high temperature, and paste products are better tested at 45 °C for 4 weeks rather than 40 °C for 1 week.
First separate a foaming problem from a foam-stability problem:
Poor foaming → pick a primary surfactant with strong foaming: GCK-95A (excellent foam and water solubility), GCK-30K (whole coconut chain, unrefined coconut origin, superior foaming), SCG-30 (good foaming and stability), A85 (abundant foam, easier to thicken)
Fast decay or coarse foam → add a stability component: CHSB-35 (improves foaming and persistence when blended with anionics), ACS-30K (efficient booster, also reduces slipperiness), CMT-35 (abundant foam, good compatibility)
Poor hard-water tolerance → PCP-30 (natural oat amino acid surfactant, good foaming and stability, hard-water tolerant), SG30H (hard-water resistant), DCK-45H (dense foam, hard-water resistant), LT90 (good hard-water performance)
These three problems often appear together. The simplest route is a pre-balanced blend (ST-35, KCB-65F, GCM-30) rather than stacking additives yourself.
We have two different "preservative-free" routes that are often confused, so separate them first:
Route one: the ingredient itself contains no preservative — grades marked preservative-free on the product page, such as KCB-95T/95F/95P, GCK-30H, GCK-30K, SCG-30N, SCG-30D, CMT-30K, HC-1BN, HC-10PBN. This only means nothing was added to that drum; it does not mean the finished product needs no preservation.
Route two: replacing conventional preservatives with a new preservation system — grades with a "new preservation" suffix, such as SCG-30WN, SCG-30DW, TCG-30WN, CA-30W, MD50M, GCK-30KAS. This is a formula-level substitution.
Our HD-SDT (self-defence technology) is the accumulated work on how to keep a system stable without conventional preservatives. One point must be clear: whether a product is genuinely preservative-free depends on the water activity, pH, pack format and production environment of the whole formula and must be verified by a preservative challenge test — you cannot judge it from the ingredient label alone.
Mildly acidic (pH 5.0–6.0) is the most common range for amino acid cleansers. Three points:
1. Pick the right grade. KCB-95P was designed for mildly acidic systems (the product page states suitability for mildly acidic systems); CT-30 / TCG-30 (TEA-cocoyl glutamate) are mildly acidic amino acid surfactants with good skin affinity, fine foam and good biodegradability
2. Watch the drop in solubility. Near the isoelectric point the solubility of some amino acid surfactants falls, which can give haze or precipitation — always trial transparent systems
3. Watch preservative efficacy. Some preservatives lose efficacy at mildly acidic pH, which is part of why we launched the "new preservation" grades
In addition, glutamate types (SCG series) are low in irritation to eyes and skin with good foaming and foam stability, which makes them the safer choice in mildly acidic cleansers.
This is an area we have been recognised for (MP80 received a "Top Ten Innovative Ingredients" award at the China Cosmetics Science and Technology Festival in 2019). The 4 current grades fall into two approaches:
Where minimum irritation matters (eye-area applications)
· MP80 (PEG-6 caprylic/capric glycerides + propylene glycol + PEG/PPG-25/30 copolymer, patented) — odourless, no haze, no residue; suitable for developing eye-area makeup removers
· MP90 (new) — EWG green-rated, good makeup solvency, fresh and moisturising
Where natural origin and oil replacement matter
· RP-80F — EO-free, natural origin, suitable for eye-area use; replaces cleansing oil for heavy makeup with a fresh skin feel
Where skin feel and safety need balancing
· TO310 — mild emollient, fast makeup solvency, moisturising without greasiness; the product page states non-irritating, non-comedogenic and non-sensitising
Decide first on the makeup intensity you are targeting (daily sunscreen / light makeup / heavy waterproof) and whether eye-area use is required, then choose the grade.
Yes. We have grades specifically marked cold-processable:
· DCK-45M, DCK-45H, DCP-30H, DCB-45H, DCB-40M (natural oil soap series)
· KS-300 (potassium laurate + potassium myristate + potassium palmitate + glycerin + water)
Three points on cold processing:
1. Liquid raw materials can thicken or partly solidify in cold weather and need to be brought back to a flowable state before charging
2. Thickening in a cold-process system relies on the crystallisation behaviour of the ingredients themselves — do not force it with added electrolyte
3. Cold processing removes the heating pasteurisation step, so microbiological control of water and equipment has to be stricter
Following a "reduce irritation first" principle, choose from our mild surfactant line:
· Ultra-mild amphoterics: SN40 (sodium cocoyl amphoacetate hydroxypropyl sulfonate, good compatibility, low eye irritation), CM48 (disodium cocoyl amphodiacetate, stated ultra-mild on the product page)
· Stated for baby care and sensitive skin: SLGC (sodium lauryl glycol carboxylate; the product page states suitable for baby care and sensitive skin products)
· Lowering the irritation of the primary surfactant: C-32 (sodium cocoyl amphoacetate, reduces the irritation of AES systems)
· Convenient four-component blend: ST-35 (product page states natural, safe and mild, abundant and dense foam, moisturising without dryness)
· Amino acid route: LG30 (sodium lauroyl glutamate, suited to sensitive skin), SCG-30 (low irritation to eyes and skin)
One point that must be stated: mildness data on an ingredient is not the same as a "suitable for sensitive skin" conclusion on a finished product. Whether to make that claim is for the brand owner to decide after completing human patch testing and the required safety and efficacy evaluation.
Any of three ways:
1. Fill in the sample request form on the Contact Us page (/contact.html)
2. Add our WeCom account (QR codes on the right side of the site and in the footer)
3. Email sales@hondugroup.com directly, or call Shanghai +86-021-64820758 / Guangzhou +86-020-86469166
Once the request is in, we follow our five-step SOP: customer raises the issue → project planning → project development → feedback and communication → project summary and acceptance. If you only need standard grades for comparison, we ship samples directly; if you need a specific formula problem solved, we do project planning first and then send samples with a suggested formula.
The more complete the brief, the fewer round trips. Ideally state in one go:
· Target product: cleansing paste / cleansing mousse / body wash / shampoo / makeup remover / scrub / other
· System type: pure amino acid / soap based / amino-acid-soap hybrid / sulfate system / surfactant-free
· Target pH range (this decides solid versus liquid grade)
· Appearance requirement: transparent / pearlescent / opaque white / coloured, and whether it must resist graining
· Skin feel target: fresh / moisturising / less slippery / dense foam
· Cost band and target dosage
· Line capability: heating available, cold processing possible, vacuum homogeniser or not
· Regulation and market: destination country or region (this affects whether extra documents are needed)